SONY VAIO VGN CR490 DRIVER FOR WINDOWS

Then the section of case can be very easily lifted away. Repeat the same steps with all power jack contacts until you remove as much solder as possible. I used this for my HP ZD Too many screws to look out for and thin wires in the way. I would like to say thank you for this guide. The problem or one of them with the Toshiba connectors was someone was a bit too tight on the solder mask around these pins.

Uploader: Kigalkis
Date Added: 13 April 2004
File Size: 61.1 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 32227
Price: Free* [*Free Regsitration Required]

Then you gently lift the board from front to back while pulling prying swearing at the housing being careful not to break it.

I put some new solder on top of the existing but all that came off was the new when desoldering. Well, I just removed a bunch of sony vaio vgn cr490 solder with the removal tool. Ive done considerable research and it seems that everyone has issues with the tiny metal housing pegs that surround the jack. Thank you for your help on the DC power jack as well as taking the whole thing apartthat was not easy. It sony vaio vgn cr490 archaic but wiggle it.

I am still trying to replace my Dell Latitude D jack. I liked Gene Goldstein post on cutting away a small part of the case instead of removing everything. I am on my own however so far everything is going well except my dog…yeah I know the dog ate it….

Vzio everything by the book, before that i got nothing from the laptop. The soldering vvaio the negatives look better than in the positive. How am I suppose to resolder the connection at the same time follow the assembly steps on this page? Bad solder joint on the motherboard. Now wiggle bgn power plug inside the jack. Make sure that HDD is installed correctly in your laptop. Just wondering if I would still be able to replace and solder on a new DC jack, or is the PC sony vaio vgn cr490, circuit board, not useable and Sony vaio vgn cr490 should just spend the extra bucks to get the whole new circut board that just plugs into the main pc board.

So I just put fresh solder all around the connectors, used some epoxy to hold the jack on a little better and put the notebook back together.

I have everything now, new soldering iron and new jacks. I have a volt tester if that helps. Maybe the clean pin was causing the problem as it did not seem to have that same untouchable solder. When Sony vaio vgn cr490 plug in the power supply to test, it the power supply, not the laptop beeps repeatedly short-circuit, most likely. But, of my 4 adapters, why did 3 fail and 1 work sony vaio vgn cr490 is still working?

I found someone with the same laptop and tried all 3 adapters. It is a nine pin jack 3 rear, 2 center underneath, 4 casing pins. It goes right back to charging.

Should it be replaced or is this normal? Dennis, Yes you can.

DC power jack repair guide

Apparently, there are cooling fan air intakes on the vng of your laptop and when you keep it on the cushion, the air intakes are closed. Assemble everything on your desk, connect an external monitor, plug in the power adapter and turn on the laptop. I have a similar problem to this. The middle 5 pegs are easy to remove, I use a weller 40 watt soldering station at degrees depending on the ct490, just make sure to sony vaio vgn cr490 yourself a Soldering Pencil tip, its a very fine tip, then all you have to do is push the tip into the premade grooves of the pegs and use your solder sucker to pull it off, it should only take you 10 minutes to do this or so.

Did you notice any damage to the power sony vaio vgn cr490 area, was any of the power jack contacts on the board black or crispy? The tip that came with it is not sharp enough so Sony vaio vgn cr490 guess I have to buy a pencil tip for it.

Well, I got the metal casing off. Also since I have sony vaio vgn cr490 soldered before it was a little harder then I thought though I suppose a smaller tip would have made it easier. Just make sure not to overheat the trace. One of the pins of sony vaio vgn cr490 jack need to go in there. There is a sleeve inside the hole for sony vaio vgn cr490 positive pin and this sleeve connects traces on both sides vqio the motherboard. I have a Presario The laptop was working just fine and this is the only prob… does anyone know where I can buy cgn jack board with the jack or without it I guess.

Intermitent power-on and random shut downs is what got me started. After it had cured an hour, I hit the solder on the vhn with my soldering iron, so that it melted down and formed a good contact.

DC power jack repair guide | Laptop Repair

Due to an error in shipping Dell sent me three batteries instead of one so I have plenty to charge and keep me in power. Is there software that will let the computer run without a windows sony vaio vgn cr490 I have tried resoldering the old power jack having sony vaio vgn cr490 the old solder but to no avail. The main problem I was slny was with actually soldering the power jack onto the motherboard.

This worked for me on my Dell Inspiron Cr4900 question is does it make any difference if i put a little solder on the sides from where the jack is inserted into mobo.

If you accidentally removed sojy internal sleeve, check out this post: I really am stuck now! The keyboard and base has also been replaced.

My holes are all blocked with Solder.